Showing posts with label Modular. Show all posts
Showing posts with label Modular. Show all posts

Monday, February 27, 2012

Wall Plate Jack Considerations | Modular Wall Plates



Modular wall plates are the most common type of wall plate in use for data cabling because they meet the various ANSI/TIA and NEC standards and codes for quality data communications cabling. So modular wall plates have the widest variety of jack types available. All the jacks available today differ based on a few parameters, including the following:
  • Wall plate system type
  • Cable connection
  • Jack orientation
  • ANSI/TIA-568-C.2 and -C.3 wiring pattern

Wall Plate System Type

Remember how the type of wall plate you use dictates the type of jacks for that wall plate? Well, logically, the reverse is also true. The interlocking system that holds the jack in place in the wall plate differs from brand to brand. So, when you pick a certain brand and manufacturer for a jack, you must use the same brand and manufacturer of wall plate.

Cable Connection

Jacks for modern communication applications use insulation displacement connectors (IDCs), which have small metal teeth or pins in the connector that press into the individual wires of a UTP cable (or the wires are pressed into the teeth). The teeth puncture the outer insulation of the individual wires and make contact with the conductor inside, thus making a connection. This process (known as crimping or punching down, depending on the method or tool used) is illustrated in Figure 1.

 
Figure 1: Using insulation displacement connectors (IDCs)
Though they may differ in methods, any connector that uses some piece of metal to puncture through the insulation of a strand of copper cable is an IDC connector.

Jack Orientation

Yes, jack orientation. The individual wall plate systems use many different types of jacks, and some of those systems use jacks with positions other than straight ahead (which is the "standard" configuration). These days, a popular configuration is a jack that's angled approximately 45 degrees down. There are many reasons that this jack became popular. Because it's angled, the cable-connect takes up less room (which is nice when a desk is pushed up tight against the wall plate). The angled connector works well in installations with high dust content because it's harder for dust to rest inside the connector. It is especially beneficial in fiber-to-the-desktop applications because it avoids damage to the fiber-optic patch cord by greatly reducing the bend radius of the cable when the cable is plugged in. Figure 2 shows an example of an angled connector.

 
Figure 2: A faceplate with angled RJ-45 and coaxial connectors
Note 
Angled connectors are found in many different types of cabling installations, including ScTP, UTP, and fiber optic.

Wiring Pattern

When connecting copper RJ-45 jacks for universal applications (according to the standard, of course), you must wire all jacks and patch points according to either the T568-A or T568-B pattern. Figure 3 shows one side of a common snap-in jack to illustrate that the same jack can be terminated with either T568-A or T568-B color coding. (You may want to see the color version of this figure in the color section.) By comparing Table 1 and 2, you can see that the wiring schemes are different only in that the positions of pair 2 (white/orange) and pair 3 (white/green) are switched. If your company has a standard wiring pattern and you wire a single jack with the opposing standard, that particular jack will not be able to communicate with the rest of the network.

 
Figure 3: A common snap-in jack showing both T568-A and T568-B wiring schemes
Table 1 shows the wiring color scheme for the T568-A pattern. Notice how the wires are paired and which color goes to which pin. Table 2 shows the same for T568-B.
Table 1: Wiring Scheme for T568-A 
Pin Number
Wire Color
1
White/green
2
Green
3
White/orange
4
Blue
5
White/blue
6
Orange
7
White/brown
8
Brown
Table 9.3: Wiring Scheme for T568-B 
Pin Number
Wire Color
1
White/orange
2
Orange
3
White/green
4
Blue
5
White/blue
6
Green
7
White/brown
8
Brown

Friday, February 24, 2012

Number of Jacks | Modular Wall Plates



The first decision you must make when using modular wall plates is how many jacks you want in each wall plate. Each opening in the wall plate can hold a different type of jack for a different type of cable media, if necessary. Additionally, each jack must be served by its own cable, and at least one of those should be a four-pair, 100 ohm, UTP cable.
The number of jacks a plate can have is based on the size of the plate. Fixed-design wall plates mainly come in one size. Modular plates come in a couple of different sizes. The smallest size is single-gang, which measures 4.5″ high and 2.75″ wide. The next largest size is called double-gang, which measures 4.5″ by 4.5″ (the same height as single-gang plates but almost twice as wide). There are also triple- and quad-gang plates, but they are not used as often as single- and double-gang plates. Figure 1 shows the difference between a single- and double-gang wall plate.

 
Figure 1: Single- and double-gang wall plates
Each manufacturer has different guidelines about how many openings for jacks fit into each type of wall plate. Most manufacturers, however, agree that six jacks are the most you can fit into a single-gang wall plate.
With the advent of technology and applications such as videoconferencing and fiber-to-the-desktop, users need more jacks and different types of cabling brought to the desktop. You can bring Category 3, Category 5e, or Category 6 UTP cable, fiber-optic and coaxial cable all to the desktop for voice, data, and video with 6-, 12- and 16-jack wall plates.

Tuesday, February 7, 2012

Labeling | Modular Wall Plates



Just like fixed-design wall plates, modular wall plates use labels to differentiate the different jacks by their purpose. In fact, modular wall plates have the widest variety of labels—every modular wall plate manufacturer seems to pride itself on its varied colors and styles of labeling. However, as with fixed-design plates, the labels are either text (e.g.,LAN, Phone) or pictures of their intended use, perhaps permanently molded in the plate or on the jack.